diagnostic – A I D A

diagnostic – A I D A https://aida.ixla.it Machine and perso control Mon, 10 Jul 2023 08:13:31 +0000 it-IT hourly 1 https://wordpress.org/?v=6.7.2 https://aida.ixla.it/wp-content/uploads/2023/06/cropped-icon-1-32x32.png diagnostic – A I D A https://aida.ixla.it 32 32 Board Properties https://aida.ixla.it/?p=150 Fri, 23 Jun 2023 14:17:44 +0000 https://aida.ixla.it/?p=150 System parameters are listed in this AIDA section. This list is device dependent and it can change from system to system, is displayed for diagnostic purpose only

Counters

Machine and laser lifetime

Name	Description	Value
Diode	Diode hours counter	0
System	System hours counter	0

SystemTemperatures

Real time system temperature monitoring

Name	Description	Value
Diode	Temperature of diode (in Celsius)	0
Driver	Temperature of driver (in Celsius)	56.85
Heatsink	Temperature of heatsink (in Celsius)	0

Serial Numbers

Electronic boards and components serial number

Name	Description	Value
BoardSerial	Serial number of the laser board.	A0288/17/22-002
TransportSerial	Serial number of the transport module.	A0286/17/22-101

System Voltage

Real time monitoring of single module power supply

Name	Description	Value
ScanHead	Real Time Scanner Head Power[V]	15.17
PcPower	Real Time PC Power[V]	12.01
PowerSupply	Real Time AC/DC Converter Output Power [V]	24.04

DiodeTEC Measures

Real time control of laser sources power supply and temperature

Name	Description	Value
DiodeCurrent	Real Time Diode Current Measure [A]	0
DiodeVoltage	Real Time Diode Current Measure [V]	0
TECCurrent	Real Time Diode TEC Current Measure [A]	0
TECVoltage	Real Time Diode TEC Current Measure [V]	0

SystemParamSetup

Laser source current and temperature factory setting

Name	Description	Value
DiodeTemperatureSetPoint	Diode Temperature Setpoint (in Celsius)	0
DiodeCurrentSetPoint	Diode Current Setpoint (A)	0
TECVoltage	TEC Voltage Setpoint [V]	0

]]> Control Center https://aida.ixla.it/?p=148 Fri, 23 Jun 2023 14:17:29 +0000 https://aida.ixla.it/?p=148

the control center allows to manage the basic functions of the system. It performs the main commands and allows to perform simple customization cycles. Useful for demos, diagnostics and troubleshooting:

LOAD CARD

picks up a document from the hopper and takes it to the next station. The destination depends on the system title. In desktop systems the target is the laser position, in modular systems the first module after the feeder

FLIP CARD

flip the card on the opposite side in case of card personalization system. This command is not available on passport personalization system

EJECT CARD

The card or passport is ejected into the output bin

RESET TRANSPORT

Reset the document trasport, clean the path and, where available, reject eventual cards inside the unit

LOAD TEMPLATE

Load one of the Jobtemplate available on the application

START RED POINTER

Enable the laser diode to simulate the printing using the red aiming beam

STOP RED POINTER

Switch off the laser diode used as aiming beam

MARK FRONT

If the job template has been loaded the mark front button will start the laser personalization. The button is disabled if no template has been loaded or laser is not enabled (i.e: interlock)

MARK REAR

If the job template has been loaded the mark rear button will start the laser personalization. The button is disabled if no template has been loaded or laser is not enabled (i.e: interlock)

]]> Transport https://aida.ixla.it/?p=146 Fri, 23 Jun 2023 14:17:16 +0000 https://aida.ixla.it/?p=146

in this section it is possible to execute basic commands of the document transport module. The two combo boxes represent the starting position and the final destination of the document to be moved.
The selection must be coherent with the state of the machine and the document position along the trasnport line.
The position of the document is highlighted by the status of the relative module represented in the lower boxes.

]]>